Flow and Heat Transfer Analysis in Lead-bismuth Reactor Core under Rod Bending Condition

QIU Hanrui; LI Jun; WANG Mingjun; ZHANG Jing; TIAN Wenxi; SU Guanghui

doi:10.7538/yzk.2022.youxian.0799

Atomic Energy Science and Technology > 2023 > 57(8): 1514-1524. > DOI: 10.7538/yzk.2022.youxian.0799

QIU Hanrui, LI Jun, WANG Mingjun, ZHANG Jing, TIAN Wenxi, SU Guanghui. Flow and Heat Transfer Analysis in Lead-bismuth Reactor Core under Rod Bending Condition[J]. Atomic Energy Science and Technology, 2023, 57(8): 1514-1524. DOI: 10.7538/yzk.2022.youxian.0799

Citation:

PDF (16206 KB)

Flow and Heat Transfer Analysis in Lead-bismuth Reactor Core under Rod Bending Condition

State Key Laboratory of Multiphase Flow in Power Engineering, School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
Shaanxi Key Laboratory of Advanced Nuclear Energy and Technology, School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049, China

More Information

Graphical Abstract

Abstract

Abstract

Liquid metal-cooled fast reactors (LMFRs) are being investigated in many countries as the next-generation nuclear reactors. Fuel rods in LMFRs are commonly arranged in a triangular pitch and assembled in a hexagonal fuel wrapper. The fuel pin will be subjected to various forces during the irradiation process, leading to the phenomena of bending and deformation. As a result, the performance of the fuel assembly is directly related to reactor safety, reliability, and economy. To investigate the effect of rod bending on the flow and heat transfer characteristics, a computational fluid dynamics (CFD) model of the Karlsruhe Institute of Technology (KIT) 19 rods fuel assembly has been built. The model contains 19 duel rods using lead-bismuth eutectic as working fluid. The mesh of the assembly with and without wire, correlation method of turbulence model and fluid-solid coupling heat transfer were considered in the CFD model. The established model was validated, and the simulation results were found to be in good agreement with experimental data. The simulation results indicated that the SST k-ω turbulent model and Cheng-Tak turbulent Prandtl correlation can be combined to precisely obtain the flow and heat transfer behavior of the coolant in sub-channels. The results show that in the case of neglecting the wire spacer, the rod bending narrows the coolant channel and forms a local high-temperature region. In the deviating direction of bending, the coolant channel widens, promoting mixing and causing coolant temperature to decrease. The maximum circumferential temperature difference of the center rod bending, edge rod bending, and corner rod bending is 46 K, 17 K and 16 K, respectively. In the case of considering the wire spacer, the geometry of the bending rod has been simplified. The influence of the bending wire on the coolant flow resistance is reduced, which results in the failure to reflect the deterioration of coolant heat transfer due to bending. Therefore, the high-temperature region generated by rod bending is less significant due to the wire mixing effect, the high-temperature area is mainly concentrated in the narrow area where the rod contacts the wire. This study reveals the effect of fuel rod performance on the safety and reliability of lead-bismuth reactors, which provides a reference for the reactor safety design. Further study is necessary to reveal the complex heat transfer characteristics and flow mechanism in the case of rod bending with wire spacer. The work presented in this paper represents an important step toward the research on fuel rod bending scenarios in the LMFR fuel assembly.
- lead-bismuth reactor,
- fuel assembly,
- fuel rod bending,
- CFD method,
- reactor thermal-hydraulics

FullText(HTML)

References (25)

References

[1]	于晓勇，祁沛垚，乔守旭，等. 5×5棒束通道局部阻塞流场实验研究[J]. 原子能科学技术，2021，55(11)：1976-1983. YU Xiaoyong, QI Peiyao, QIAO Shouxu, et al. Experimental study of flow field in 5×5 rod bundle channel under local blocking condition[J]. Atomic Energy Science and Technology, 2021, 55(11): 1976-1983(in Chinese).
[2]	魏诗颖，王成龙，田文喜，等. 铅基快堆关键热工水力问题研究综述[J]. 原子能科学技术，2019，53(2)：326-336. WEI Shiying, WANG Chenglong, TIAN Wenxi, et al. Research progress in key thermal-hydraulic issue of lead-based fast reactor[J]. Atomic Energy Science and Technology, 2019, 53(2): 326-336(in Chinese).
[3]	何少鹏，王明军，章静，等. 基于OpenFOAM的液态金属铅铋三维流动换热特性数值模拟研究[J]. 原子能科学技术，2021，55(6)：1007-1014. HE Shaopeng, WANG Mingjun, ZHANG Jing, et al. Numerical simulation of three-dimensional flow heat transfer characteristics of liquid lead-bismuth using OpenFOAM[J]. Atomic Energy Science and Technology, 2021, 55(6): 1007-1014(in Chinese).
[4]	RASU N G, VELUSAMY K, SUNDARARAJAN T, et al. Thermal hydraulic effect of porous blockage in fuel subassembly of sodium cooled fast reactor[J]. Annals of Nuclear Energy, 2014, 70: 64-81.
[5]	MIYAZAKI K, KIMURA J, OGWA M, et a1. Temperature fluctuation of sodium in annular now channel heated by single-pin with blockage[J]. Journal of Nuclear science and Technology, 1978, 15(1): 10-23.
[6]	刘洋，喻宏，周志伟. 钠冷快堆燃料组件热工水力特性数值模拟与分析[J]. 原子能科学技术，2014，48(10)：1790-1796. LIU Yang, YU Hong, ZHOU Zhiwei. Numerical simulation and analysis on thermal-hydraulic behavior of fuel assembly for sodium-cooled fast reactor[J]. Atomic Energy Science and Technology, 2014, 48(10): 1790-1796(in Chinese).
[7]	孙畅，焦守华，柴翔，等. 基于CFD方法的铅铋冷却燃料棒束的热工水力特性分析[J]. 原子能科学技术，2020，54(8)：1386-1394. SUN Chang, JIAO Shouhua, CHAI Xiang, et al. Thermal hydraulic analysis of LBE-cooled rod bundle based on CFD method[J]. Atomic Energy Science and Technology, 2020, 54(8): 1386-1394(in Chinese).
[8]	田文喜，王明军，秋穗正，等. 基于CFD方法的核动力系统热工安全特性研究进展[J]. 原子能科学技术，2019，53(10)：1968-1982. TIAN Wenxi, WANG Mingjun, QIU Suizheng, et al. Review on safety characteristic research progress of nuclear power plant thermal-hydraulics using CFD method[J]. Atomic Energy Science and Technology, 2019, 53(10): 1968-1982(in Chinese).
[9]	WANG Mingjun, WANG Yingjie, TIAN Wenxi, et al, Recent progress of CFD applications in PWR thermal hydraulics study and future directions[J]. Annals of Nuclear Energy, 2021, 150: 107836.
[10]	刘凯，王明军，田文喜，等. 数值反应堆堆芯通道级三维热工水力程序CorTAF开发及初步验证[J]. 原子能科学技术，2022，56(2)：261-270. LIU Kai, WANG Mingjun, TIAN Wenxi, et al. Development and preliminary validation of three-dimensional subchannel thermal-hydraulic analysis code CorTAF for numerical reactor core[J]. Atomic Energy Science and Technology, 2022, 56(2): 261-270(in Chinese).
[11]	PACIO J, DAUBNER M, FELLMOSER F, et al. Heavy-liquid metal heat transfer experiment in a 19-rod bundle with grid spacers[J]. Nuclear Engineering and Design, 2014, 273: 33-46.
[12]	PACIO J, DAUBNER M, FELLMOSER F, et al. Experimental study of heavy-liquid metal (LBE) flow and heat transfer along a hexagonal 19-rod bundle with wire spacers[J]. Nuclear Engineering and Design, 2016, 301: 111-127.
[13]	PACIO J, WETZEL T, DOOLAAR H, et al. Thermal-hydraulic study of the LBE-cooled fuel assembly in the MYRRHA reactor: Experiments and simulations[J]. Nuclear Engineering and Design, 2017, 312: 327-337.
[14]	HE Shaopeng, WANG Mingjun, ZHANG Jing, et al. Numerical simulation of three-dimensional flow and heat transfer characteristics of liquid lead-bismuth[J]. Nuclear Engineering and Technology, 2021, 53(6): 1834-1845.
[15]	CHEN Jing, ZHANG Dalin, SONG Ping, et al. CFD investigation on thermal-hydraulic behaviors of a wire-wrapped fuel subassembly for sodium-cooled fast reactor[J]. Annals of Nuclear Energy, 2018, 113: 256-269.
[16]	WANG Yingjie, WANG Mingjun, ZHANG Jing, et al. Large eddy simulation of the mixing characteristics of liquid sodium at the core outlet of sodium cooled fast reactors[J]. Annals of Nuclear Energy, 2021, 159: 108347.
[17]	LI Jun, FANG Di, GUO Chao, et al. Numerical study on the thermal hydraulic characteristics in a wire-wrapped assembly of LFR[J]. Front Energy Res, 2020, 8: 548065.
[18]	GE Z, LIU J, ZHAO P, et al. Investigation on the applicability of turbulent-Prandtl-number models in bare rod bundles for heavy liquid metals[J]. Nuclear Engineering and Design, 2017, 314: 198-206.
[19]	CHEN F, HUAI X, CAI J, et al. Investigation on the applicability of turbulent-Prandtl-number models for liquid lead-bismuth eutectic[J]. Nuclear Engineering and Design, 2013, 257: 128-133.
[20]	ZHANG Y, WANG C, LAN Z, et al. Review of thermal-hydraulic issues and studies of lead-based fast reactors[J]. Renewable and Sustainable Energy Reviews, 2020, 120: 109625.
[21]	CHENG X, TAK N I. CFD analysis of thermal-hydraulic behavior of heavy liquid metals in sub-channels[J]. Nuclear Engineering and Design, 2006, 236: 1874-1885.
[22]	DOVIZIO D, MIKU B, SHAMS A, et al. Validating RANS to predict the flow behavior in wire-wrapped fuel assemblies[J]. Nuclear Engineering and Design, 2020, 356: 110376.
[23]	DOVIZIO D, SHAMS A, ROELOFS F. Numerical prediction of flow and heat transfer in an infinite wirewrapped fuel assembly[J]. Nuclear Engineering and Design, 2019, 349: 193-205.
[24]	刘凯，李林峰，王明军，等. 基于CFD方法的矩形窄缝通道内过冷流动沸腾模型研究[J]. 原子能科学技术，2022，56(10)：2041-2050. LIU Kai, LI Linfeng, WANG Mingjun, et al. Model investigation of subcooled flow boiling in narrow rectangular channel using CFD method[J]. Atomic Energy Science and Technology, 2022, 56(10): 2041-2050(in Chinese).
[25]	CHENG S, TODREAS N E. Hydrodynamic models and correlations for bare and wire-wrapped hexagonal rod bundles-bundle friction factors, subchannel friction factors and mixing parameters[J]. Nuclear Engineering and Design, 1986, 92: 227-251.

Cited By

Get Citation

PDF

XML

Article views (149) PDF downloads (145)

Turn off MathJax

Article Contents

Abstract

References

Flow and Heat Transfer Analysis in Lead-bismuth Reactor Core under Rod Bending Condition

Abstract

References

Catalog

Export File

Citation

Format

Content