压水堆驱动线落棒历程计算
Calculation of Drop Course of Control Rod Assembly in PWR
-
摘要: 控制棒落棒性能验证是核电厂安全分析的重要部分，研制驱动线落棒历程计算程序有利于验证和改进控制棒驱动线设计。基于驱动线结构特点，分析运动组件的受力情况并进行分解，选择理论或数值方法逐一求取各分力的瞬态值，从而建立驱动线落棒历程的循环步进计算程序。利用秦山核电二期工程驱动线落棒性能试验数据对理论模型和程序计算结果进行对比验证。结果证明：所建立的驱动线落棒历程计算程序适用于压水堆驱动线系统，能正确地对运动组件落棒受力与运动历程进行模拟。Abstract: The validation of control rod drop performance is an important part of safety analysis of nuclear power plant. Development of computer code for calculating control rod drop course will be useful for validating and improving the design of control rod drive line. Based on structural features of the drive line, the driving force on moving assembly was analyzed and decomposed, the transient value of each component of the driving force was calculated by choosing either theoretical method or numerical method, and the simulation code for calculating rod cluster control assembly (RCCA) drop course by time step increase was achieved. The analysis results of control rod assembly drop course calculated by theoretical model and numerical method were validated by comparing with RCCA drop test data of Qinshan Phase Ⅱ 600 MW PWR. It is shown that the developed RCCA drop course calculation code is suitable for RCCA in PWR and can correctly simulate the drop course and the stress of RCCA.
-
Keywords:
- drive line ,
- control rod assembly ,
- drop course
-
-
[1] 于建华，魏永涛，孙磊，等. 控制棒组件在流体环境中下落时所受阻力的计算[J]. 核动力工程，2001，22（3）：236-241.YU Jianhua, WEI Yongtao, SUN Lei, et al. Computation of resistance force of dropping control rod assembly under environment of fluid[J]. Nuclear Power Engineering, 2001, 22（3）: 236-241(in Chinese). [2] 赵良举，彭云康，谭曙时. 秦山600 MW核反应堆控制棒热态落棒实验模拟分析[J]. 核动力工程，2003，24（3）：211-214.ZHAO Liangju, PENG Yunkang, TAN Shushi. Numerical simulation and analysis of control rod dropping of Qingshan 600 MWe Nuclear Reactor[J]. Nuclear Power Engineering, 2003, 24（3）: 211-214(in Chinese). [3] 窦一康，姚伟达，杨仁安，等. 事故工况下控制棒落棒时间分析方法及其工程应用[C]∥第十届全国反应堆结构力学会议论文专辑. 上海：中国核学会，1998：371-376. [4] ANDRIAMBOLOLONA H, BOSSELUT D, MASSIN P. Methodology for a numerical simulation of an insertion or a drop of the rod cluster control assembly in a PWR[J]. Nuclear Engineering and Design, 2007, 237: 600-606. [5] 叶奇蓁，张敬才，黄坚持，等. 秦山核电二期工程反应堆堆内构件流致振动综合评价[J]. 核动力工程，2003，24（2）：82-86.YE Qizhen, ZHANG Jingcai, HUANG Jianchi, et al. Reactor internals FIV synthetical assessment for Qinshan Phase Ⅱ NPP Project[J]. Nuclear- Power Engineering, 2003, 24（2）: 82-86(in Chinese). [6] 王树众，王栋，林宗虎. 竖直环形管道内的两相流摩擦阻力研究[J]. 西安交通大学学报，1994，28（5）：101-109.WANG Shuzhong, WANG Dong, LIN Zonghu. A study of the two-phase frictional pressure drop in vertical annular channels[J]. Journal of Xi’an Jiaotong University, 1994, 28（5）: 101-109(in Chinese). [7] SADATOMI M, SATO Y. Two phase flow in vertical noncircular channel[J]. Int J Multiphase Flow, 1982, 8(6): 641-655. [8] 景思睿，张鸣远. 流体力学[M]. 西安：西安交通大学出版社，2001:216-223. [9] 钟艳敏，王源，付仿松. 秦山核电二期工程反应堆控制棒落棒性能测试[J]. 核动力工程，2003，24(2)：221-223.ZHONG Yanmin, WANG Yuan, FU Fangsong. Drop performance testing of Qinshan Phase Ⅱ NPP Probject[J]. Nuclear Power Engineering, 2003, 24（2）: 221-223(in Chinese). [10] 孙磊，于建华，魏永涛，等. 控制棒组件落棒时间与历程计算[J]. 核动力工程，2003，24（1）：59-62.SUN Lei, YU Jianhua, WEI Yongtao, et al. Analysis of drop-time and course of control rod assembly[J]. Nuclear Power Engineering, 2003, 24（1）: 59-62(in Chinese).
计量
- 文章访问数: 262
- HTML全文浏览量: 0
- PDF下载量: 1117
下载:
